Amsoil Synthetic Compressor Oil – ISO32, SAE 10W (PCH)

Amsoil Synthetic Compressor Oil - ISO32, SAE 10W (AWI)
Amsoil Synthetic Compressor Oil - ISO32, SAE 10W (PCH)
ISO32, SAE 10W (PCH)
Data Bulletin 

Product Highlights

The correct viscosity grade compressor oil is recommended for use in rotary screw, rotary vane, reciprocating and other compressor applications. Compatible with PAO, ester- and petroleum-based compressor oils. Not compatible with glycol- or silicone-based compressor oils.

AMSOIL PC Series Synthetic Compressor Oil is a long-life, premium compressor lubricant based on novel, proprietary technology. It incorporates the highest quality, thermally stable PAO synthetics fortified with premium non-detergent additives for maximum protection at high temperatures. It lasts up to 8,000 hours, effectively reducing maintenance and waste oil disposal costs.

Improves Compressor Efficiency

AMSOIL PC Series Oil has low friction properties, resists viscosity increase from oxidation and helps improve operating efficiency.

Controls Foam and Reduces Wear

AMSOIL PC Series Oil contains anti-foam additives and, unlike some other compressor oils, is anti-wear fortified. Good foam control reduces heat, oxidation and wear. High contact regions are protected against wear for increased compressor life and lower maintenance costs.

Package Sizes (PCH)

Code Sizes Units
PCH05 (PCH05-EA) 5-Gallon Pail Each
PCH55 (PCH55-EA) 55-Gallon Drum Each
PCH27 (PCH27-EA) 275-Gallon Tote Each

Resists Water Contamination

Water from condensation builds up in compressors and can cause unwanted oil/water emulsions that lead to rust and corrosion. AMSOIL PC Series Oil is hydrolytically stable. It resists acid formation, readily separates from water and is anti-rust fortified. Water can be easily drained for simplified disposal and increased oil life.

Resists Heat and Oxidation

AMSOIL PC Series Oil combines the inherent stability of premium synthetic base oils with specialized anti-oxidant additives to resist varnish, carbon and acid formation. It is formulated to protect compressors better and last longer in service than petroleum oils, especially during hot operating conditions.

Safety Advantage

AMSOIL PC Series Oil is an ashless, high-flash-point formulation with very low carbon-forming tendencies that minimizes the incidence of ignition-promoting “hot spots.” While PC Series Oil can provide improved fire safety, it cannot be considered non-flammable.

Application Recommendations*

AMSOIL PC Series Oil in the appropriate viscosity is recommended for use in single and multistage rotary screw, vane, centrifugal and reciprocating compressor crankcases and cylinders, vacuum pumps, pressure washer pumps and other applications such as gears, bearings, blowers and pumps. In compressor applications, drain intervals of 8,000 hours or more can be expected under normal operation. Drain intervals are subject to operating conditions and maintenance practices. Monitoring by oil analysis is recommended. For best performance when converting to AMSOIL PC Series Oil, it is recommended the compressor be flushed of the old oil and all filters changed prior to the installation of PC Series Oil. If carbon deposits are present on the internal components, it is recommended they be removed following the compressor manufacturer recommendations.

* Consult the equipment manufacturer or AMSOIL Technical Services for use in specific applications.

Compatibility

AMSOIL PC Series Synthetic Compressor Oil is compatible with petroleum oils and most synthetic oils, seals, paints and materials, including the following:

Gases: • Nitrogen • Hydrogen • Helium • Carbon Monoxide • Carbon Dioxide (dry) • Ethylene • Methane • Propane • Butane • Propylene • Butylenes • Natural Gas • Benzene • Butadiene • Furnace (crack gas) • Hydrogen Sulfide (dry) • Synthetic Gas • Sulfur Dioxide

Paints: • Epoxy • Oil Resistant Alkyd • Acrylic Enamel

Plastics: • Acetal (Delrin) • ABS • Phenolic • Polyamide-imide • Polyamide (Nylon) • Polycarbonate (metal covered only) • Polyester • Polyetherimide (Nylon) • Polyimide • Polyphenylene oxide • Polystyrene • Polysulfone • PTFE (Teflon) • Terephthalate

Elastomers: • Fluoroelastomer (Viton) • Nitrile (Buna N) • Polyacrylate • TFE/P • Poly Urethane

Note: Not recommended for “breathing air” or refrigeration compressors. Not recommended for use with polycarbonate plastic that is not metal covered, PVC plastic and butyl, ethylene-propylene or SBR rubber. PC Series Oil is not compatible with polyalkylene glycol or silicone oils.

Amsoil Product Warranty

Amsoil products are backed by a Limited Liability Warranty. For complete information visit www.amsoil.com/warranty.aspx.

TYPICAL TECHNICAL PROPERTIES
Amsoil Synthetic Compressor Oil – ISO32, SAE 10W (PCH)
ISO Viscosity Grade (ASTM D2422) 32
Kinematic Viscosity @100°C cSt (ASTM D 445) 6.1
Kinematic Viscosity @40°C cSt (ASTM D 445) 32.8
Viscosity Index (ASTM D 2270) 135
Flash Point °C (°F) (ASTM D 92) 260 (500)
Fire Point °C (°F) (ASTM D 92) 274 (525
Pour Point °C (°F) (ASTM D 97) -53 (-63)
Four-Ball Wear Test (ASTM D 4172)
(40 kg, 1200 rpm, 75°C, 60 min.)
0.45
Specific Gravity, g/mL (ASTM D1298) 0.8393
Density, lb/gal (ASTM D1298) 6.989
Copper Strip Corrosion Test (ASTM D130) 1A
Foam Tendency, Seq. I, II, III (ASTM D892) 0/0/0
Dielectric Strength, voltage, kV AC (ASTM D877) 45.4
Demulsibility (ASTM D1401) 40-40-0 (10)
Rust Test (ASTM D665 A & B)
Fresh Water and Synthetic Sea Water
Pass

Amsoil Synthetic Compressor Oil – ISO46, SAE 20W (PCI)

Amsoil Synthetic Compressor Oil - ISO46, SAE 20W (PCI)
Amsoil Synthetic Compressor Oil - ISO46, SAE 20W (PCI)
ISO46, SAE 20W (PCI)
Data Bulletin 

Product Highlights

The correct viscosity grade compressor oil is recommended for use in rotary screw, rotary vane, reciprocating and other compressor applications. Compatible with PAO, ester- and petroleum-based compressor oils. Not compatible with glycol- or silicone-based compressor oils.

AMSOIL PC Series Synthetic Compressor Oil is a long-life, premium compressor lubricant based on novel, proprietary technology. It incorporates the highest quality, thermally stable PAO synthetics fortified with premium non-detergent additives for maximum protection at high temperatures. It lasts up to 8,000 hours, effectively reducing maintenance and waste oil disposal costs.

Improves Compressor Efficiency

AMSOIL PC Series Oil has low friction properties, resists viscosity increase from oxidation and helps improve operating efficiency.

Controls Foam and Reduces Wear

AMSOIL PC Series Oil contains anti-foam additives and, unlike some other compressor oils, is anti-wear fortified. Good foam control reduces heat, oxidation and wear. High contact regions are protected against wear for increased compressor life and lower maintenance costs.

Package Sizes (PCI)

Code Sizes Units
PCIQT (PCIQT-EA) Quart Each
PCIQT (PCIQT-CA) Quart Case of 12
PCI05 (PCI05-EA) 5-Gallon Pail Each
PCI30 (PCI30-EA) 30-Gallon Drum Each
PCI55 (PCI55-EA) 55-Gallon Drum Each
PCI27 (PCI27-EA) 275-Gallon Tote Each

Resists Water Contamination

Water from condensation builds up in compressors and can cause unwanted oil/water emulsions that lead to rust and corrosion. AMSOIL PC Series Oil is hydrolytically stable. It resists acid formation, readily separates from water and is anti-rust fortified. Water can be easily drained for simplified disposal and increased oil life.

Resists Heat and Oxidation

AMSOIL PC Series Oil combines the inherent stability of premium synthetic base oils with specialized anti-oxidant additives to resist varnish, carbon and acid formation. It is formulated to protect compressors better and last longer in service than petroleum oils, especially during hot operating conditions.

Safety Advantage

AMSOIL PC Series Oil is an ashless, high-flash-point formulation with very low carbon-forming tendencies that minimizes the incidence of ignition-promoting “hot spots.” While PC Series Oil can provide improved fire safety, it cannot be considered non-flammable.

Application Recommendations*

AMSOIL PC Series Oil in the appropriate viscosity is recommended for use in single and multistage rotary screw, vane, centrifugal and reciprocating compressor crankcases and cylinders, vacuum pumps, pressure washer pumps and other applications such as gears, bearings, blowers and pumps. In compressor applications, drain intervals of 8,000 hours or more can be expected under normal operation. Drain intervals are subject to operating conditions and maintenance practices. Monitoring by oil analysis is recommended. For best performance when converting to AMSOIL PC Series Oil, it is recommended the compressor be flushed of the old oil and all filters changed prior to the installation of PC Series Oil. If carbon deposits are present on the internal components, it is recommended they be removed following the compressor manufacturer recommendations.

* Consult the equipment manufacturer or AMSOIL Technical Services for use in specific applications.

Compatibility

AMSOIL PC Series Synthetic Compressor Oil is compatible with petroleum oils and most synthetic oils, seals, paints and materials, including the following:

Gases: • Nitrogen • Hydrogen • Helium • Carbon Monoxide • Carbon Dioxide (dry) • Ethylene • Methane • Propane • Butane • Propylene • Butylenes • Natural Gas • Benzene • Butadiene • Furnace (crack gas) • Hydrogen Sulfide (dry) • Synthetic Gas • Sulfur Dioxide

Paints: • Epoxy • Oil Resistant Alkyd • Acrylic Enamel

Plastics: • Acetal (Delrin) • ABS • Phenolic • Polyamide-imide • Polyamide (Nylon) • Polycarbonate (metal covered only) • Polyester • Polyetherimide (Nylon) • Polyimide • Polyphenylene oxide • Polystyrene • Polysulfone • PTFE (Teflon) • Terephthalate

Elastomers: • Fluoroelastomer (Viton) • Nitrile (Buna N) • Polyacrylate • TFE/P • Poly Urethane

Note: Not recommended for “breathing air” or refrigeration compressors. Not recommended for use with polycarbonate plastic that is not metal covered, PVC plastic and butyl, ethylene-propylene or SBR rubber. PC Series Oil is not compatible with polyalkylene glycol or silicone oils.

Amsoil Product Warranty

Amsoil products are backed by a Limited Liability Warranty. For complete information visit www.amsoil.com/warranty.aspx.

TYPICAL TECHNICAL PROPERTIES
Amsoil Synthetic Compressor Oil – ISO46, SAE 20W (PCI)
ISO Viscosity Grade (ASTM D2422) 46
Kinematic Viscosity @100°C cSt (ASTM D 445) 7.3
Kinematic Viscosity @40°C cSt (ASTM D 445) 43.0
Viscosity Index (ASTM D 2270) 132
Flash Point °C (°F) (ASTM D 92) 252 (486)
Fire Point °C (°F) (ASTM D 92) 274 (529)
Pour Point °C (°F) (ASTM D 97) -47 (-53)
Four-Ball Wear Test (ASTM D 4172)
(40 kg, 1200 rpm, 75°C, 60 min.)
0.45
Specific Gravity, g/mL (ASTM D1298) 0.8428
Density, lb/gal (ASTM D1298) 7.018
Copper Strip Corrosion Test (ASTM D130) 1A
Foam Tendency, Seq. I, II, III (ASTM D892) 0/0/0
Dielectric Strength, voltage, kV AC (ASTM D877) 45.4
Demulsibility (ASTM D1401) 40-40-0 (10)
Rust Test (ASTM D665 A & B)
Fresh Water and Synthetic Sea Water
Pass

Amsoil Synthetic Compressor Oil – ISO68, SAE30 (PCJ)

Amsoil Synthetic Compressor Oil - ISO68, SAE30 (PCJ)
Amsoil Synthetic Compressor Oil - ISO68, SAE30 (PCJ)
ISO68, SAE30 (PCJ)
Data Bulletin 

Product Highlights

The correct viscosity grade compressor oil is recommended for use in rotary screw, rotary vane, reciprocating and other compressor applications. Compatible with PAO, ester- and petroleum-based compressor oils. Not compatible with glycol- or silicone-based compressor oils.

AMSOIL PC Series Synthetic Compressor Oil is a long-life, premium compressor lubricant based on novel, proprietary technology. It incorporates the highest quality, thermally stable PAO synthetics fortified with premium non-detergent additives for maximum protection at high temperatures. It lasts up to 8,000 hours, effectively reducing maintenance and waste oil disposal costs.

Improves Compressor Efficiency

AMSOIL PC Series Oil has low friction properties, resists viscosity increase from oxidation and helps improve operating efficiency.

Controls Foam and Reduces Wear

AMSOIL PC Series Oil contains anti-foam additives and, unlike some other compressor oils, is anti-wear fortified. Good foam control reduces heat, oxidation and wear. High contact regions are protected against wear for increased compressor life and lower maintenance costs.

Package Sizes (PCJ)

Code Sizes Units
PCJQT (PCJQT-EA) Quart Each
PCJQT (PCJQT-CA) Quart Case of 12
PCJ05 (PCJ05-EA) 5-Gallon Pail Each
PCJ30 (PCJ30-EA) 30-Gallon Drum Each
PCJ55 (PCJ55-EA) 55-Gallon Drum Each
PCJ27 (PCJ27-EA) 275-Gallon Tote Each

Resists Water Contamination

Water from condensation builds up in compressors and can cause unwanted oil/water emulsions that lead to rust and corrosion. AMSOIL PC Series Oil is hydrolytically stable. It resists acid formation, readily separates from water and is anti-rust fortified. Water can be easily drained for simplified disposal and increased oil life.

Resists Heat and Oxidation

AMSOIL PC Series Oil combines the inherent stability of premium synthetic base oils with specialized anti-oxidant additives to resist varnish, carbon and acid formation. It is formulated to protect compressors better and last longer in service than petroleum oils, especially during hot operating conditions.

Safety Advantage

AMSOIL PC Series Oil is an ashless, high-flash-point formulation with very low carbon-forming tendencies that minimizes the incidence of ignition-promoting “hot spots.” While PC Series Oil can provide improved fire safety, it cannot be considered non-flammable.

Application Recommendations*

AMSOIL PC Series Oil in the appropriate viscosity is recommended for use in single and multistage rotary screw, vane, centrifugal and reciprocating compressor crankcases and cylinders, vacuum pumps, pressure washer pumps and other applications such as gears, bearings, blowers and pumps. In compressor applications, drain intervals of 8,000 hours or more can be expected under normal operation. Drain intervals are subject to operating conditions and maintenance practices. Monitoring by oil analysis is recommended. For best performance when converting to AMSOIL PC Series Oil, it is recommended the compressor be flushed of the old oil and all filters changed prior to the installation of PC Series Oil. If carbon deposits are present on the internal components, it is recommended they be removed following the compressor manufacturer recommendations.

* Consult the equipment manufacturer or AMSOIL Technical Services for use in specific applications.

Compatibility

AMSOIL PC Series Synthetic Compressor Oil is compatible with petroleum oils and most synthetic oils, seals, paints and materials, including the following:

Gases: • Nitrogen • Hydrogen • Helium • Carbon Monoxide • Carbon Dioxide (dry) • Ethylene • Methane • Propane • Butane • Propylene • Butylenes • Natural Gas • Benzene • Butadiene • Furnace (crack gas) • Hydrogen Sulfide (dry) • Synthetic Gas • Sulfur Dioxide

Paints: • Epoxy • Oil Resistant Alkyd • Acrylic Enamel

Plastics: • Acetal (Delrin) • ABS • Phenolic • Polyamide-imide • Polyamide (Nylon) • Polycarbonate (metal covered only) • Polyester • Polyetherimide (Nylon) • Polyimide • Polyphenylene oxide • Polystyrene • Polysulfone • PTFE (Teflon) • Terephthalate

Elastomers: • Fluoroelastomer (Viton) • Nitrile (Buna N) • Polyacrylate • TFE/P • Poly Urethane

Note: Not recommended for “breathing air” or refrigeration compressors. Not recommended for use with polycarbonate plastic that is not metal covered, PVC plastic and butyl, ethylene-propylene or SBR rubber. PC Series Oil is not compatible with polyalkylene glycol or silicone oils.

Amsoil Product Warranty

Amsoil products are backed by a Limited Liability Warranty. For complete information visit www.amsoil.com/warranty.aspx.

TYPICAL TECHNICAL PROPERTIES
Amsoil Synthetic Compressor Oil – ISO68, SAE30 (PCJ)
ISO Viscosity Grade (ASTM D2422) 68
Kinematic Viscosity @100°C cSt (ASTM D 445) 10.5
Kinematic Viscosity @40°C cSt (ASTM D 445) 68.1
Viscosity Index (ASTM D 2270) 145
Flash Point °C (°F) (ASTM D 92) 250 (482)
Fire Point °C (°F) (ASTM D 92) 276 (529)
Pour Point °C (°F) (ASTM D 97) -40 (-40)
Four-Ball Wear Test (ASTM D 4172)
(40 kg, 1200 rpm, 75°C, 60 min.)
0.45
Specific Gravity, g/mL (ASTM D1298) 0.8524
Density, lb/gal (ASTM D1298) 7.098
Copper Strip Corrosion Test (ASTM D130) 1A
Foam Tendency, Seq. I, II, III (ASTM D892) 0/0/0
Dielectric Strength, voltage, kV AC (ASTM D877) 45.4
Demulsibility (ASTM D1401) 40-40-0 (5)
Rust Test (ASTM D665 A & B)
Fresh Water and Synthetic Sea Water
Pass

Amsoil Synthetic Compressor Oil – ISO100, SAE30/40 (PCK)

Amsoil Synthetic Compressor Oil - ISO100, SAE30/40 (PCK)
Amsoil Synthetic Compressor Oil - ISO100, SAE30/40 (PCK)
ISO100, SAE30/40 (PCK)
Data Bulletin 

Product Highlights

The correct viscosity grade compressor oil is recommended for use in rotary screw, rotary vane, reciprocating and other compressor applications. Compatible with PAO, ester- and petroleum-based compressor oils. Not compatible with glycol- or silicone-based compressor oils.

Package Sizes (PCK)

Code Sizes Units
PCKQT (PCKQT-EA) Quart Each
PCKQT (PCKQT-CA) Quart Case of 12
PCK05 (PCK05-EA) 5-Gallon Pail Each
PCK30 (PCK30-EA) 30-Gallon Drum Each
PCK55 (PCK55-EA) 55-Gallon Drum Each
PCK27 (PCK27-EA) 275-Gallon Tote Each

AMSOIL PC Series Synthetic Compressor Oil is a long-life, premium compressor lubricant based on novel, proprietary technology. It incorporates the highest quality, thermally stable PAO synthetics fortified with premium non-detergent additives for maximum protection at high temperatures. It lasts up to 8,000 hours, effectively reducing maintenance and waste oil disposal costs.

Improves Compressor Efficiency

AMSOIL PC Series Oil has low friction properties, resists viscosity increase from oxidation and helps improve operating efficiency.

Controls Foam and Reduces Wear

AMSOIL PC Series Oil contains anti-foam additives and, unlike some other compressor oils, is anti-wear fortified. Good foam control reduces heat, oxidation and wear. High contact regions are protected against wear for increased compressor life and lower maintenance costs.

Resists Water Contamination

Water from condensation builds up in compressors and can cause unwanted oil/water emulsions that lead to rust and corrosion. AMSOIL PC Series Oil is hydrolytically stable. It resists acid formation, readily separates from water and is anti-rust fortified. Water can be easily drained for simplified disposal and increased oil life.

Resists Heat and Oxidation

AMSOIL PC Series Oil combines the inherent stability of premium synthetic base oils with specialized anti-oxidant additives to resist varnish, carbon and acid formation. It is formulated to protect compressors better and last longer in service than petroleum oils, especially during hot operating conditions.

Safety Advantage

AMSOIL PC Series Oil is an ashless, high-flash-point formulation with very low carbon-forming tendencies that minimizes the incidence of ignition-promoting “hot spots.” While PC Series Oil can provide improved fire safety, it cannot be considered non-flammable.

Application Recommendations*

AMSOIL PC Series Oil in the appropriate viscosity is recommended for use in single and multistage rotary screw, vane, centrifugal and reciprocating compressor crankcases and cylinders, vacuum pumps, pressure washer pumps and other applications such as gears, bearings, blowers and pumps. In compressor applications, drain intervals of 8,000 hours or more can be expected under normal operation. Drain intervals are subject to operating conditions and maintenance practices. Monitoring by oil analysis is recommended. For best performance when converting to AMSOIL PC Series Oil, it is recommended the compressor be flushed of the old oil and all filters changed prior to the installation of PC Series Oil. If carbon deposits are present on the internal components, it is recommended they be removed following the compressor manufacturer recommendations.

* Consult the equipment manufacturer or AMSOIL Technical Services for use in specific applications.

Compatibility

AMSOIL PC Series Synthetic Compressor Oil is compatible with petroleum oils and most synthetic oils, seals, paints and materials, including the following:

Gases: • Nitrogen • Hydrogen • Helium • Carbon Monoxide • Carbon Dioxide (dry) • Ethylene • Methane • Propane • Butane • Propylene • Butylenes • Natural Gas • Benzene • Butadiene • Furnace (crack gas) • Hydrogen Sulfide (dry) • Synthetic Gas • Sulfur Dioxide

Paints: • Epoxy • Oil Resistant Alkyd • Acrylic Enamel

Plastics: • Acetal (Delrin) • ABS • Phenolic • Polyamide-imide • Polyamide (Nylon) • Polycarbonate (metal covered only) • Polyester • Polyetherimide (Nylon) • Polyimide • Polyphenylene oxide • Polystyrene • Polysulfone • PTFE (Teflon) • Terephthalate

Elastomers: • Fluoroelastomer (Viton) • Nitrile (Buna N) • Polyacrylate • TFE/P • Poly Urethane

Note: Not recommended for “breathing air” or refrigeration compressors. Not recommended for use with polycarbonate plastic that is not metal covered, PVC plastic and butyl, ethylene-propylene or SBR rubber. PC Series Oil is not compatible with polyalkylene glycol or silicone oils.

Amsoil Product Warranty

Amsoil products are backed by a Limited Liability Warranty. For complete information visit www.amsoil.com/warranty.aspx.

TYPICAL TECHNICAL PROPERTIES
Amsoil Synthetic Compressor Oil – ISO100, SAE30/40 (PCK)
ISO Viscosity Grade (ASTM D2422) 100
Kinematic Viscosity @100°C cSt (ASTM D 445) 13.4
Kinematic Viscosity @40°C cSt (ASTM D 445) 100.2
Viscosity Index (ASTM D 2270) 133
Flash Point °C (°F) (ASTM D 92) 262 (504)
Fire Point °C (°F) (ASTM D 92) 274 (525)
Pour Point °C (°F) (ASTM D 97) -44 (-47)
Four-Ball Wear Test (ASTM D 4172)
(40 kg, 1200 rpm, 75°C, 60 min.)
0.45
Specific Gravity, g/mL (ASTM D1298) 0.8550
Density, lb/gal (ASTM D1298) 7.119
Copper Strip Corrosion Test (ASTM D130) 1A
Foam Tendency, Seq. I, II, III (ASTM D892) 0/0/0
Dielectric Strength, voltage, kV AC (ASTM D877) 45.4
Demulsibility (ASTM D1401) 40-40-0 (5)
Rust Test (ASTM D665 A & B)
Fresh Water and Synthetic Sea Water
Pass

Amsoil Sirocco® Compressor Oil – ISO-32/46 (SEI)

Amsoil SIROCCO™ Compressor Oil - ISO-32/46 (SEI)
Amsoil Sirocco® Compressor Oil - ISO-32/46 (SEI)
ISO-32/46 (SEI)
Data Bulletin 

Product Highlights

SIROCCO™ is recommended as a direct replacement for PAG compressor oils such as Sullair Sullube 32 and Ingersol-Rand SSR Ultra Coolant. Not recommended for use with Silicone base fluids. Consult Amsoil for further information.

Amsoil Sirocco® Synthetic Compressor Oil is formulated with premium synthetic ester technology. This high-quality, long-life fluid lasts several times longer in use than mineral-based oils. Amsoil SIROCCO Compressor Oil is fully formulated with non-detergent additives and is designed for use in rotary screw compressors and vacuum pumps. SIROCCO effectively protects against wear, oxidation, foam and rust. Its inherent lubricity and good thermal conductivity allow it to reduce heat and energy consumption. Amsoil SIROCCO Synthetic Compressor Oil increases operating efficiency, reducing energy and maintenance costs. Amsoil SIROCCO maintains performance across a wide operating temperature range. Its low pour point, high viscosity index and lack of paraffins (wax) make it an excellent all-season lubricant. At cold temperatures, equipment starts easier and the lubricant is quickly pumped to critical components, preventing lubricant starvation and excessive wear. SIROCCO also repels water to prevent damaging oil/water emulsions, allowing for longer lubricant life and ease of water removal from the reservoir.

Performance Features

  • Resists foaming
  • Inhibits rust and oxidation
  • Readily separates from water
  • Recommended for use in rotary screw compressors
  • Long-life/extended drain performance
  • Compatible with polyglycol fluids such as Sullair® Sullube® 32 and Ingersoll-Rand® SSR Ultra-coolant®

Amsoil SIROCCO Synthetic Compressor Oil has higher flash, fire and auto-ignition points than competitive petroleum oils. Although SIROCCO increases fire safety, it cannot be considered non-flammable.

Package Sizes (SEI)

Code Sizes Units
SEIQT (SEIQT-EA) Quart Each
SEIQT (SEIQT-CA) Quart Case of 12
SEI05 (SEI05-EA) 5-Gallon Pail Each
SEI30 (SEI30-EA) 30-Gallon Drum Each
SEI55 (SEI55-EA) 55-Gallon Drum Each
SEI27 (SEI27-EA) 275-Gallon Tote Each

Amsoil Sirocco® Synthetic Compressor Oil is formulated with premium synthetic ester technology. This high-quality, long-life fluid lasts several times longer in use than mineral-based oils. Amsoil SIROCCO Compressor Oil is fully formulated with non-detergent additives and is designed for use in rotary screw compressors and vacuum pumps. SIROCCO effectively protects against wear, oxidation, foam and rust. Its inherent lubricity and good thermal conductivity allow it to reduce heat and energy consumption. Amsoil SIROCCO Synthetic Compressor Oil increases operating efficiency, reducing energy and maintenance costs. Amsoil SIROCCO maintains performance across a wide operating temperature range. Its low pour point, high viscosity index and lack of paraffins (wax) make it an excellent all-season lubricant. At cold temperatures, equipment starts easier and the lubricant is quickly pumped to critical components, preventing lubricant starvation and excessive wear. SIROCCO also repels water to prevent damaging oil/water emulsions, allowing for longer lubricant life and ease of water removal from the reservoir.

Performance Features

  • Resists foaming
  • Inhibits rust and oxidation
  • Readily separates from water
  • Recommended for use in rotary screw compressors
  • Long-life/extended drain performance
  • Compatible with polyglycol fluids such as Sullair® Sullube® 32 and Ingersoll-Rand® SSR Ultra-coolant®

Amsoil SIROCCO Synthetic Compressor Oil has higher flash, fire and auto-ignition points than competitive petroleum oils. Although SIROCCO increases fire safety, it cannot be considered non-flammable.

Application Recommendation

Amsoil SIROCCO Synthetic Compressor Oil is a multi—viscosity oil that may be used in applications calling for either an ISO 32 or ISO 46 compressor oil or coolant. It is recommended for use in single— and multi—stage rotary screw compressors and vacuum pumps.

When installing Amsoil SIROCCO Synthetic Compressor Oil, it is recommended that the old oil be thoroughly drained and, if warranted, the system cleaned. If a lot of residue is found on the internal compressor parts, follow the manufacturer’s recommendations for removal prior to installing the new oil.

Amsoil SIROCCO has a high level of solvency and may remove deposits left in the system. Check the filters and oil/air separators regularly for the first 500 hours of operation and replace as necessary.

Amsoil SIROCCO Synthetic Compressor Oil is compatible with and recommended as a replacement for higher—priced polyalkylene glycol (PAG) compressor oils or coolants such as Sullair Sullube 32 and Ingersoll Rand SSR Ultra Coolant. No flushing is necessary when changing over from glycol coolants to Amsoil SIROCCO Synthetic Compressor Oil. However, draining the system and changing the filters is recommended.

Maintenance Recommendation

The polyglycols that SCIROCCO Compressor Oil replaces hold water throughout their service life. Like most non-polyglycol compressor oils, SIROCCO separates from water, allowing it to be periodically removed from the oil. How often this needs to be done is heavily dependent upon operating conditions. Initially, the compressor should be shut down every 24 hours for 15 minutes, allowing free water to settle to the bottom of the reservoir to be drained. Noting the amount of water removed will help establish a regular maintenance interval appropriate for the conditions. Excessive water buildup in the oil can result in filter plugging and significantly shortened oil life. If you have questions contact Amsoil Technical Services at 715-399-TECH.

Service Life

Amsoil SIROCCO Synthetic Compressor Oil is recommended for use up to 8,000+ hours for most compressor applications. However, this is subject to operating conditions and maintenance practices. Monitoring by oil analysis every 1,000 hours is recommended.

Compatibility

Amsoil SIROCCO Compressor Oil is compatible with petroleum oils; most synthetic oils*; and many seals, paints and materials commonly used in compressors. Materials recommended and not recommended for use with SIROCCO Compressor Oil are listed below.

*SIROCCO Compressor Oil is NOT RECOMMENDED as a replacement for or for use with the silicone-based compressor oil Sullair® Sullube® 24 KT. Amsoil SIROCCO is NOT RECOMMENDED for use in “Breathing Air” or “Refrigeration” compressors.

Recommended Not Recommended
  • Seals – Viton®, High Nitrile Buna N (>36%), Teflon®
  • Paints – Epoxy, Oil-Resistant Alkyd, Two-Part Urethane
  • Plastics – Nylon, Delrin®, Celcon®, PBT
  • Seals – Neoprene, SBR Rubber, Low Nitrile Buna N
  • Paints – Acrylic Paint, Lacquer
  • Plastics – Polystyrene, Polycarbonate Plastic, PVC, ABS
Note: Process gases suitable for use with Amsoil SIROCCO Synthetic Compressor Oil; Nitrogen, hydrogen, helium, carbon monoxide, carbon dioxide (dry), ethylene, methane, propane, butane, propylene, butylene, natural gas, benzene, butadiene, furnace (crack gas), hydrogen sulfide (dry), synthetic gas, sulfur dioxide.

Amsoil Product Warranty

Amsoil products are backed by a Limited Liability Warranty. For complete information visit www.amsoil.com/warrantyaspx.

Amsoil Product Availability

Amsoil SIROCCO Synthetic Compressor Oil is available in 5-gallon pails, 55-gallon drums, 275-gallon totes and bulk quantities. For 275-gallon totes, please allow two to four weeks for delivery.

Sullair Sullube 32 and Sullair Sullube 24 KT are registered trademarks of Sullair Corporation; Ingersoll-Rand SSR Ultra-coolant is a registered trademark of Ingersoll-Rand Company. SIROCCO is a registered trademark of Amsoil INC.

TYPICAL TECHNICAL PROPERTIES
Amsoil Sirocco® Compressor Oil – ISO-32/46 (SEI)
ISO Viscosity Grade (ASTM D2422) 32/46
Kinematic Viscosity @100°C cSt (ASTM D 445) 6.3
Kinematic Viscosity @40°C cSt (ASTM D 445) 40.1
Viscosity Index (ASTM D 2270) 103
Flash Point °C (°F) (ASTM D 92) 252 (486)
Fire Point °C (°F) (ASTM D 92) 280 (536)
Pour Point °C (°F) (ASTM D 97) -43 (-45)
Four-Ball Wear Test (ASTM D 4172)
(40 kg, 1200 rpm, 75°C, 60 min.)
0.45
Specific Gravity, g/mL (ASTM D1298) 0.9315
Density, lb/gal (ASTM D1298) 7.757
API Gravity (ASTM D287) 20.4